CP-102UF Series
2-port Universal PCI serial over fiber boards |
|
 |
PC-based Serial |
 |
|
|
 |
 |
Extend serial transmission distance up to:
· 40 km with single-mode (CP-102UF-S)
· 5 km with multi-mode (CP-102UF-M) |
|
Supports ''Ring'' and ''Point-to-Point'' transmission modes |
|
921.6 Kbps maximum baudrate for super fast data transmission |
|
| |
|
| |
|
Introduction |
|
|
| |
The CP-102UF smart Universal PCI boards are designed for industrial automation applications that require a long distance, multi-point, PC-based data acquisition solution. The boards are compatible with all popular operating systems, and each of the 2 serial ports support data rates up to 921.6 Kbps. In addition, the CP-102UF boards work with both 3.3V and 5V PCI buses, allowing them to be installed in virtually any available PC server. With a maximum data transmission distance of 40 km (with the single-mode model), the CP-102UF cards beat the 15 meter maximum for RS-232, and even the 1.2 km maximum for RS-422/485. For many industrial applications, an even bigger benefit is that optical fiber isolates the data from dangerous increases in ground potential, ground loops, and electrical EMI/RFI electromagnetic
radiation.
|
|
 Back to Top |
|
Features |
|
|
|
 |
128-byte FIFO and on-chip H/W, S/W fl ow control |
|
|
Compatible with 3.3/5V PCI and PCI-X |
|
|
Drivers provided for Windows (Vista, 2003, XP, 2000, 98, ME), WinCE 5.0, Linux, and Unix |
|
|
Easy maintenance with on-board LED display and management software |
|
|
Immune from signal interference |
|
|
Guards against electronic degradation and chemical corrosion |
|
|
| |
Ring Operation
With the CP-102UF card, your PC can be included as one node of a fiber ring formed using Moxa's own TCF-142 serial-to-fiber converter. Since each TCF-142 has two fiber ports and one serial port, PCs that are part of the ring will be able to communicate with serial devices connected to the ring. Note that the Tx port of the CP-102UF connects to a neighboring converter's Rx port to form the ring. Once the ring has been set up, simply use the DIP switches to configure the CP-102UF to ''Ring mode.'' When one node transmits a signal, the signal travels around the ring until it returns back to the transmitting unit, which then blocks the signals. With the CP-102UF, you can set up fiber rings that are up to 100 km in total length.
|
|
Back
to Top
|
|
Specifications
|
|
|
|
| Hardware |
|
|
|
| |
| Optical Fiber Interface |
|
|
|
|
|
|
CP-102UF-M: 50/125, 62.5/125, or 100/140 μm
CP-102UF-S: 8.3/125, 8.75/125, 9/125 or 10/140 μm |
|
|
|
|
CP-102UF-M: Up to 5 km with multi-mode fi ber
CP-102UF-S: Up to 40 km with single-mode fi ber |
|
|
|
|
CP-102UF-M: 820 nm
CP-102UF-S: 1310 nm
Tx Output: -5 dBm |
|
|
|
|
CP-102UF-M: -20 dBm
CP-102UF-S: -24 dBm |
|
|
| Point-to-Point Transmission |
|
|
|
|
|
|
|
| |
| Performance |
|
|
|
| |
| Serial Communication Parameters |
|
|
|
|
|
|
|
|
|
| None, Even, Odd, Space, Mark |
|
|
|
|
|
|
|
|
|
|
|
| |
| Driver Support |
|
|
|
Windows (2000, XP/2003/Vista x86/x64), DOS, Linux 2.4/2.6,
QNX 6 |
|
|
|
|
| |
| Environmental Limits |
|
|
|
|
|
|
|
|
|
| -20 to 85°C (-4 to 185°F) |
|
|
|
|
| |
| Regulatory Approvals |
|
|
|
|
|
|
EN55024
EN 61000-3-2
EN 61000-3-3
IEC 61000-4-2(ESD)
IEC 61000-4-3(RS)
IEC 61000-4-4(EFT)
IEC 61000-4-5(Surge)
IEC 61000-4-6(CS)
IEC 61000-4-8
IEC 61000-4-11(DIPS) |
|
|
|
|
| |
| Power Requirements |
|
CP-102UF-M: 429 mA @ +5V
CP-102UF-S: 424 mA @ +5V |
|
|
|
|
| |
| Warranty |
|
| |
|
|
Ordering
Information
|
|
|
| |
 CP-102UF-M |
|
| 2-port Universal PCI serial over fi ber board with multi-mode fi ber for 5 km transmission (ST connector) |
|
|
CP-102UF-S |
|
| 2-port Universal PCI serial over fi ber board with single-mode fi ber for 40 km transmission (ST connector) |
|
|
|
| CP-102UF-M or CP-102UF-S card
Standard bracket
Document and Software CD
Quick Installation Guide (printed)
Warranty Card |
|
|
|
| |
|
